Jump to content
  • Welcome to 205GTIDrivers.com!

    Hello dear visitor! Feel free to browse but we invite you to register completely free of charge in order to enjoy the full functionality of the website.

Sign in to follow this  
SPofRCLD

Xu10j4r-xu10j4rs Differences

Recommended Posts

SPofRCLD

hello everyone,

 

I am in the middle of a pretty nice rebuilding project of a 205 gti.

now, i have a nice rebuilt 1.9 engine in the car, but seek for something a bit newer and kind more reliable

whilst having more power,

which got me to the xu10j4rs.

NOW, as I AM living in ISRAEL, things become a bit more complicated than just getting the engine, putting it in, and rewire everything..

the major issue is that none of these engines cant be approved on the 205 legally, but, i am an israeli, so i have my ways of makin it legal,

the thing is that either one of them will cost me almost the same to buy, and exactly the same amount of money and effort to legalize,

but the RFS is a highly rare engine to get your hands on in israel, so a thought crossed my mind, to take

the standard RFV xu10j4r which can be found in large amounts here as we have a lot of them xsara/xantia or whatever other car that

that engine can be found in..

 

now my question is will i be able to get close to the RFS power figures with mild changes to the RFV like manifolds and cams from a RFS engine?

what are the main differences between the engines, as ive read a lot of posts here that state that sometimes the RFV head is a better head then the RFS?

do i need to get the engine management from a RFS, or can i keep the RFV, and chip it? how to deal with the 6000 rpm cutoff then?

and basically any other good advice you can give me will be highly appreciated, as im pretty lost here...

 

Thanx,

Andrew from Israel!

Edited by SPofRCLD

Share this post


Link to post
Share on other sites
SPofRCLD

thank you for the quick reply,

read both topics, dont quite answer the questions i asked..

Share this post


Link to post
Share on other sites
SPofRCLD

could someone please shed some light on this matter? i have read most of the posts on this forum that include the xu10j4 in, and didnt get

the final conclusion to my questions..

Share this post


Link to post
Share on other sites
petert
now my question is will i be able to get close to the RFS power figures with mild changes to the RFV like manifolds and cams from a RFS engine?

 

Yes. Put bigger cams in than RFS though. They're still very mild.

 

what are the main differences between the engines, as ive read a lot of posts here that state that sometimes the RFV head is a better head then the RFS?

 

Bugger all in the head. Just minor valve sizes. Ports are huge like Mi16. Valve sizes are the same as Mi16.

 

do i need to get the engine management from a RFS, or can i keep the RFV, and chip it? how to deal with the 6000 rpm cutoff then?

 

Use after market ECU and bigger injectors.

Share this post


Link to post
Share on other sites
magic

The xu10j4rs makes 163 hp the xu10j4 132 hp

So with a inlet and exhaust manifold swap from xu10j4rs to xu10j4r you can get 98 kw at the wheels .

I saw it on a dyno day here in Sydney ..you need to remap the xu10j4r ecu

the rev limiter is on this engines 7400 rpm , thats how i set it when i remap a xu10j4rs or R ecu

Share this post


Link to post
Share on other sites
Anthony

Can I please remind people that this is a technical section of a CAR related forum, and not the place to be "discussing" sensitive political issues? Thanks.

Share this post


Link to post
Share on other sites
SPofRCLD

thank you anthony,

and thanx to petert and magic for spot on answers.

really appreciated!

Share this post


Link to post
Share on other sites
jengis

This is the way I see it - If you want to get RFS specifications you need to get the RFS head and put it on in place of the RFV head. But if the heads are as rare as the complete engine thats no help to you!

 

As for the differences, the searches should show that there are some significant differences - like very large ports and bigger valves with double springs and different cam profiles...etc. The reason some say that the XU10j4r head is better is when you need a blank canvas to customise your own port shapes. The smaller ports allow you remove only the material you want to remove.

 

Its been said that by using the well designed manifolds from the RFS is a good improvement on the lower spec engine but I don't know how much of the power difference is due to head and how much to manifolds - you will probably never know for sure without trying yourself. The tubular exhaust mainfold in particular is quite obviously better than the RFV one

 

As for the ECU, is the rev limit on the XU10j4r (RFV) really only 6k??

Share this post


Link to post
Share on other sites
B1ack_Mi16

I tohught it was the 1.8 16V head that had smaller ports, and that the RFV and RFS engines have almost identical ports apart from small differences in valve sizes.

 

An RFV with manifolds and camshafts from the RFS should be almost equal to the RFS itself.

 

Then just get it mapped to the new specs or get an aftermarket management...

Share this post


Link to post
Share on other sites
jengis
I tohught it was the 1.8 16V head that had smaller ports, and that the RFV and RFS engines have almost identical ports apart from small differences in valve sizes.

 

An RFV with manifolds and camshafts from the RFS should be almost equal to the RFS itself.

 

Then just get it mapped to the new specs or get an aftermarket management...

 

You are right, getting mixed up. :lol:

 

looking back at Sandy's measurements, the ports are only slightly smaller in the RFV, but different all the same. But perhaps not by as much as i was making out, and yes, the XU7's are significantly smaller again.

Share this post


Link to post
Share on other sites
petert
This is the way I see it - If you want to get RFS specifications you need to get the RFS head and put it on in place of the RFV head. But if the heads are as rare as the complete engine thats no help to you!

 

The RFV port sizes and valve sizes are basically identical to Mi16, but has several advantages over Mi16 - lighter valves and smaller combustion chamber. RFV engines are a bargain.

Share this post


Link to post
Share on other sites
Guest JasonS

Just going to jump in on this thread rather than start another similar one as such.

 

My question is:

Does anyone know if there are any valve clearance issues by using the GTi-6 head (XU10J4RS) on the XU10J4 bottom end? As i'm sure there are differences in the pistons between both, i.e valve cut-outs on the GTi-6 b/end?

Share this post


Link to post
Share on other sites
DorgersGTI

here an other thread jumper,

 

How can we declare the differnce in compression ratio?

 

From what i understand the RS has an ratio of 10,8:1 and de R has an ratio of 10,4:1

 

Is it in the head or in the pistons?

 

 

I have an seized rfs engine and i want an rfv block and put an rfs head on it.

 

Greeting Dennis Orgers

Share this post


Link to post
Share on other sites
large

From the looks of it an S. :ph34r:

Share this post


Link to post
Share on other sites
welshpug

the 10J4R have dished pistons.

Share this post


Link to post
Share on other sites
Guest JasonS
the 10J4R have dished pistons.

 

So therefore no issues with valve clearance if using an RS head on an R bottom end?

Share this post


Link to post
Share on other sites
welshpug

no, but the compression will be lower, but not if you fit RS pistons to get the compression back up, or if you want cams with more lift @ TDC some aftermarket ones with deeper cutouts.

Share this post


Link to post
Share on other sites
B1ack_Mi16
Just going to jump in on this thread rather than start another similar one as such.

 

My question is:

Does anyone know if there are any valve clearance issues by using the GTi-6 head (XU10J4RS) on the XU10J4 bottom end? As i'm sure there are differences in the pistons between both, i.e valve cut-outs on the GTi-6 b/end?

 

The GTi6 head on top of the S16 XU10J4 engine will up the compression to approx 10.8:1 so same as in GTi6 engine.

The S16 head has some more chamber volume than gti6 one.

Share this post


Link to post
Share on other sites
whizzer71
The RFV port sizes and valve sizes are basically identical to Mi16, but has several advantages over Mi16 - lighter valves and smaller combustion chamber. RFV engines are a bargain.

 

Ive just gat my hands on one of these engines,over and above 6 manifolds and a pair of cams what else can I do (Basic stuff/mods) to wring more power out of it ?

 

:D

Share this post


Link to post
Share on other sites
whizzer71

Ive just gat my hands on one of these engines,over and above 6 manifolds and a pair of cams what else can I do (Basic stuff/mods) to wring more power out of it ?,If I fit RS cams would it be worth getting them ground first ? (Live close to Kent + Piper cams)

 

:D

Edited by whizzer71

Share this post


Link to post
Share on other sites
welshpug

different pistons to allow for more lift.

Share this post


Link to post
Share on other sites
welshpug

dug out some info I remember seeing in the Haynes manual, the earlier 3 bolt camshaft pulleys used on the R, RS and 7JP4 are marked on the rear of the hub with a single digit.

 

J4R has the inlet numbered 3, the exhaust numbered 4, the RS engine uses 2x No4's.

 

the 7JP4 engine is numbered 1 on the inlet, 2 on the exhaust.

 

the pulley itself is the same, though I'm unsure if the same numbering exists on the later single bolt pulleys, they do all share the same arrangement again.

Share this post


Link to post
Share on other sites
nick9one1

I have somehow only just noticed this thread! I have an xu10j4r engine that has now been running since xmas eve in the 205. I picked it up for £140 including the gearbox. It seems very quick, and a great improvement over the 1.9 even though it is rated as only 5bhp more. I also have an rs head I picked up for £30 that I was planning on swapping in. I haven't quite decided if I am going to swap the whole head or just the cams yet. (as swapping the head requires more work). after that there is just the manifolds and ecu to do.

 

for anyone thinking of using the xu10j4r one less thing to worry about is that the exhaust manifold doesn't reed re-angling as it just bolts on!

 

doesn't the r have a lower compression ratio too?

Edited by nick9one1

Share this post


Link to post
Share on other sites
amin

Hey

Dose anybody knows about differences between cranks, bearings and iron blocks of tow xu10j4rs and xu10j4r engines?and can i replace these parts from one to another?

Share this post


Link to post
Share on other sites
Sign in to follow this  

×