Jump to content
  • Welcome to 205GTIDrivers.com!

    Hello dear visitor! Feel free to browse but we invite you to register completely free of charge in order to enjoy the full functionality of the website.

Sign in to follow this  
vicious-monkey87

1.6 Carb Advice

Recommended Posts

vicious-monkey87

ok so i basically know nothing about carbs (apart from what i've read on here) and as i want to put my 1.6 on twin 40's i've just bought these:

 

a171_1.JPG

 

i was hoping that someone could tell me, what else i'll need to fit this to my car? i understand i'll need to change the fuel pump?

any general advice would be much appreciated!

 

cheers

Share this post


Link to post
Share on other sites
Tom Fenton

You don't neccesarily need to change the pump, what you do need to do is get the pressure right down to suit the carbs- typically only a few psi. You will also need a cable linkage to suit.

Share this post


Link to post
Share on other sites
vickiw106

as tom fenton has said you can use your origional pump

 

i have just done thos to my rally car you need

 

fuel pressure regulator

pedal conversion kit

2 throttle cables

and a throttle linkeage kit

 

you will also need to get the carbs jetted and balanced but your local rolling road should be able to do that

Share this post


Link to post
Share on other sites
vicious-monkey87

well the guy who sold me the webers said that they have already been jetted for a 1.6 GTi. does that mean i won't need to take it to a rolling road? (i probably will anyway)

 

throttle cables - do i just need two standard ones?

pedal conversion kit - i wasn't aware of this at all, where would i get this from and how much should i expect to pay for it?

Share this post


Link to post
Share on other sites
Baz

It'll still need to be set up though. What chokes, mains, jets etc are in them too?

Share this post


Link to post
Share on other sites
vicious-monkey87

i have no idea! i didn't know to ask the guy lol

i'll email him now and ask!

my mate is a mechanic and says he can set up the carbs for me, apparently it just takes patience, and he says he'll fit them for me although i want to do as much of it myself as possible!

Share this post


Link to post
Share on other sites
vickiw106
well the guy who sold me the webers said that they have already been jetted for a 1.6 GTi. does that mean i won't need to take it to a rolling road? (i probably will anyway)

 

throttle cables - do i just need two standard ones?

pedal conversion kit - i wasn't aware of this at all, where would i get this from and how much should i expect to pay for it?

 

 

i got my linkeage from rally nuts please see the linkeage below

 

throttle linkeage

 

you still want to have the carbs setup on your engine on the rolling road even though the carbs may be set up for a 1.6 gti a good rolling road will tune them to the engines envrioment ie different exhaust/manifold year of engine etc

 

hope this helps

Share this post


Link to post
Share on other sites
vicious-monkey87

thats great thanks :)

which one will i need for my setup? would the top mounted ones foul the bonnet?

 

what about the throttle cables? are they expensive and where would i source them?

Share this post


Link to post
Share on other sites
vickiw106
thats great thanks :)

which one will i need for my setup? would the top mounted ones foul the bonnet?

 

what about the throttle cables? are they expensive and where would i source them?

 

i am running the top mounted twin cable lp2000 i am running a standard bonnett and they are no where near

 

here's a link for the cables

Edited by vickiw106

Share this post


Link to post
Share on other sites
vicious-monkey87

thanks again!

it says in the tutorial for fitting them (on the main site) that the top mounted ones could touch the bonnet!

can i fit either type to my carbs? or do certain carbs take top mounted linkages while others take bottom mounted?

Share this post


Link to post
Share on other sites
Sign in to follow this  

×